Description
Application
- For 4G63T Mitsubishi Lancer EVO 1~3, Galant VR-4, DSM 1G / 2G, Eagle Talon, Plymouth Laser turbo upgrade
- Kinugawa turbo Subaru FA20 series turbo upgrade
- Horsepower Range: 450~550HP
The maximum power stated for each turbocharger has been calculated based strictly on the choke flow of the compressor map (total turbo capability), which represents the potential flywheel power. Performance results of this product are highly dependent upon your vehicle’s modifications and tuning/calibration.
CHRA Size
- TF06-18K
WHEEL SPEC
Bearing Type
- Journal Bearing with 360-degree performance thrust bearing kit
Cooling Type
- oil and water cooling
The set includes
- 1 x CHRA
- 1 x banjo bolt w/ washer for turbo oil feed side
(#414-01101-008 + #416-01003-007*2)
- 1 x oil return gasket
(#413-02006-001)
- 2 x banjo bolts w/ washer for turbo water coolant side
(#414-01101-019*2 + #416-01003-008*4)
- 1 x Balance Report with Anti-Counterfeit Tag
Situation
- Brand New
- Full balance from Schenk MBRS 110 Germany
Provider
- Kinugawa Turbo Systems
Warranty
- No
- For 4G63T Mitsubishi Lancer EVO 1~3, Galant VR-4, DSM 1G / 2G, Eagle Talon, Plymouth Laser turbo upgrade
- Kinugawa turbo Subaru FA20 series turbo upgrade
- Horsepower Range: 450~550HP
The maximum power stated for each turbocharger has been calculated based strictly on the choke flow of the compressor map (total turbo capability), which represents the potential flywheel power. Performance results of this product are highly dependent upon your vehicle’s modifications and tuning/calibration.
CHRA Size
- TF06-18K
WHEEL SPEC
-Compressor wheel: 55.1 / 75 mm (7+7 Point Milling / Third-Order Surface)
This high-performance 75mm compressor blends quick response and top-end power with OE reliability. The billet 18KX billet compressor wheel utilizes their latest generation blade aero with 7 primary blades and 7 splitter blades for a max flow rate of 54lb/min. This turbo is capable of producing 500+whp with a built engine and supporting modifications.
| Free Surface | Ruled Surface | |
| Process | Point Milling | Flank Milling |
| Machining Time | Slow 120 mins.each | Quick 15 mins.each |
| Characters |
1. Free Surface can be only produced by Point Milling | 1. Ruled Surface can be produced by Flank Milling 2. Low efficiency 3. Only suitable to the very easy design of compressor wheel 4. Mainly for fundamental mechanical engineering such as Centrifugal compressor |
- Turbine wheel: 54 / 61.5 mm (9 blades sts)
Note: The 9 blades STS (Superior Turbine Strike) turbine wheel. This will take a shorter time to build a boost and at higher RPM won't choke because it's less restrictive than an 11 or 12 blades turbine.
Bearing Type
- Journal Bearing with 360-degree performance thrust bearing kit
Cooling Type
- oil and water cooling
The set includes
- 1 x CHRA
- 1 x banjo bolt w/ washer for turbo oil feed side
(#414-01101-008 + #416-01003-007*2)
- 1 x oil return gasket
(#413-02006-001)
- 2 x banjo bolts w/ washer for turbo water coolant side
(#414-01101-019*2 + #416-01003-008*4)
- 1 x Balance Report with Anti-Counterfeit Tag
Situation
- Brand New
- Full balance from Schenk MBRS 110 Germany
Provider
- Kinugawa Turbo Systems
Warranty
- No