The total amount above $399, we offer free shipping and responsible for import duties.



Kinugawa Turbocharger 3" Inlet Anti-Surge TF06-18K Point Milling for SUBARU Impreza WRX STi GC GD GR Stage 2 500WHP

Regular price $1,079.00



Descriptions
This high-performance 75mm compressor blends quick response and top-end power with OE reliability. The billet 18KX billet compressor wheel utilizes their latest generation blade aero with 7 primary blades and 7 splitter blades for a max flow rate of 54lb/min. This turbo is capable of producing 500+whp with a built engine and supporting modifications.
Application
- 2002-2014 Subaru WRX
- 2004-2016 Subaru WRX STI vehicles
- 2004-2007 Subaru Forester
- It can replace TD04L WRX turbo, for IHI VF30, vf35 ... turbo directly without modification
Horsepower
- 450~550WHP
The maximum power stated for each turbocharger has been calculated based strictly on the choke flow of the compressor map (total turbo capability), which represents the potential flywheel power. Performance results of this product are highly dependent upon your vehicle’s modifications and tuning/calibration.


Kinugawa Turbo Systems Third-order surface compressor wheel
Free Surface Ruled Surface
Process Point Milling Flank Milling
Machining Time Slow 120 mins.each Quick 15 mins.each
Characters


1. Free Surface can be only produced by Point Milling
2. More air pressure and increase much better flow efficiency.
3. Mainly for high-efficiency turbochargers.

1. Ruled Surface can be produced by Flank Milling
2. Low efficiency
3. Only suitable to the very easy design of compressor wheel
4. Mainly for fundamental mechanical engineering such as Centrifugal compressor

- Turbine wheel: 54 / 61.5 mm (9 blades sts)
Note: The 9 blades STS (Superior Turbine Strike) turbine wheel. This will take a shorter time to build a boost and at higher RPM won't choke because it's less restrictive than an 11 or 12 blade turbine.

CHRA Size
- TF06-18KX

Wheels Spec
- Compressor wheel: 55.1 / 75 mm (7+7 Point Milling / Third-Order Surface) 
Ruled Surface Free Surface
Process Flank Milling Point Milling
Machining Time Quick 15 mins.each Slow 120 mins.each
Characters 1. Ruled Surface can be produced by Flank Milling
2. Low efficiency
3. Only suitable to the very easy design of compressor wheel
4. Mainly for fundamental mechanical engineering such as Centrifugal compressor
1. Free Surface can be only produced by Point Milling
2. More air pressure and increase much better flow efficiency.
3. Mainly for high efficiency turbochargers.

- Turbine wheel: 61.5 / 54 mm (9 Blades STS)

Compressor Housing AR60
- Compressor inlet : 3" hose coupler
- Compressor outlet:  2.0"  hose coupler

Turbines Housing
High-Ni Thermal resistant 
Kinugawa Subaru Turbocharger Turbine Map

Bearing Type
- Journal Bearing Systems with 360-degree thrust bearing kit

Cooling Type
- Water and Oil Cooling System

Actuator Pressure
1.0 bar is a default setup
- Available to 0.3bar, 0.5bar, 0.8bar, 1.2bar, 1.5bar, 1.7bar, and 2.0bar, Please add a comment to your order if you must change it.

Boost / HP
- Horsepower: 450~500whp
- The Max boost level is limited: 2.8bar

The set includes
- 1 x Oil supply set
- 1 x water supply and return pipe set
- 1 x Return Oil Pipeline
- 1 x turbine inlet and outlet gasket
- 5 x Stud And Nut Sets
- 1 x Turbocharger
- 1 x Balance Report with Anti-Counterfeit Tag 

Situation
-Brand New
-Full balance from SCHENK MBRS 110 Germany

Provider
-Kinugawa Turbo Systems

Guarantee
-One year


Kinugawa STS Turbin Wheel

Kinugawa Turbo Systems Billet Compressor Wheel and 360 Dynamic Thrust Bearing
Kinugawa Turbo Systems Compressor Map TD02-TD08
Kinugawa Turbo Systems SCHENK Balancer
Kinugawa Turbo Systems Anti-Counterfeit Tag


`